Rental Trailer 23815 – High Vacuum Extraction

High Vacuum Extraction Blower Module:

(2) Rotary claw vacuum pump, with a 15 HP 208-230V/3P motor:

• Motor: TEFC (Suitable for CL 1 DIV 2)
• Performance at inlet of blower: 750 SCFM at 22” Hg
• Discharge temperature: 320F at an inlet of 68 F
• Noise rating: 85 dBA
• Integral inlet
• Integral vacuum relief valve
• Air dilution valve with filter silencer

Inlet piping to each blower to contain the following components:

• One (1) 6” Solberg inlet filter/silencer
• One (1) Vacuum gauges
• PVC suction manifold to each of the blowers

Discharge piping from blower to contain:

• 6” SCH40 carbon steel pipe
• Sample port
• Pressure gauge 0-100 IWC
• Temperature gauge, 50-500 Deg F
• Galvanized steel piping to be terminated outside of enclosure with 10’ Aluminum exhaust stack with rain cap (Shipped loose for installation on site by others)

Refurbished Vapor Liquid Separator Module:

AWS-120, 120 G vapor liquid separator with:

• Marine Grade 5052 Aluminum construction
• 4” I/O
• 6” clean out
• Sight glass with column level switch assembly:
  • High level alarm switch
  • High level pump control switch
  • Low level pump control switch
• Manual drain plumbed to exterior of enclosure

Vapor inlet piping to vapor liquid separator to contain:

• Vacuum gauge
• Sample port
• 6” SCH80 PVC piping

Self Priming Centrifugal transfer pump with 2 HP 208-230V/3P motor:

• Performance: Capable of 40 GPM at 10.0 PSIG
• Motor: TEFC (Suitable for CL 1 DIV 2)

Water inlet piping to pump to contain the following components:

• Ball valve
• Wye Strainer

Water discharge piping to contain the following components:

• Pressure gauge
• Sample port
• Gate valve
• Check valve
• 1” SCH80 PVC recirculation line with gate valve
• 2” SCH80 PVC piping to be terminated outside of enclosure

SVE Manifold:

Qty. 1 4” Aluminum SVE Headers with (8) 2” Schd 80 PVC legs for each header, each leg to contain:

• Gate Valve
• Vacuum gauge
• Clear PVC Site tube (12” section)
• 2” FMPT Schedule 80 PVC piping terminated outside of enclosure

Air Sparge Compressor:

One (1) Rotary Claw sparge compressor with 15 HP 230/460V/3P motor

• Motor: TEFC (Suitable for CL 1 DIV 2)
• Performance: 165 CFM at 20 PSI
• Discharge temperature: 220F
• Noise rating: 82 dBA

Compressor assembly to contain:

• Pressure Relief Valve
• Inlet Filter
• 2” Galvanized Discharge piping
• 2” Bleed line with silencer/Muffler
• Discharge Gate Valve
• Discharge Pressure Gauge
• Discharge Temperature Gauge

Compressor Heat Exchanger:

• ½ HP 230 volt 1 phase TEFC Motor
• Delta approach of 110 Degree F
• Discharge pressure gauge
• Discharge temperature gauge
• Condensate drain line
• Galvanized steel piping

Sparge Manifold: (mounted on exterior trailer wall)

2” Aluminum Sparge Header with (9) 1” Schedule aluminum legs, each leg to contain:

• Ball Valve
• Pressure gauge
• Check Valve
• 1” MPT piping terminated outside of enclosure

Oil Water Separator Module:

Model OWS-40, 40 GPM oil water separator with:

• Designed for oils with a specific gravity of less than 0.90
• 25 micron removal size
• SS Construction
• Gasket sealed lid
• Adjustable rotary skimmer
• Easily removable coalescing media
• Ventilation stack
• Elevated table
• Gravity drain to poly pump out tank
• Sight glass with level switch assembly. Switch assembly to contain:
  • High-high level alarm switch
  • High level pump control switch
  • Low level pump control switch
• Manual drains

Ebara centrifugal transfer pump with 2 HP, 208/230V/3P motor:

• Performance: Capable of 50 GPM at 30 PSIG
• Motor: TEFC (Suitable for CL 1 DIV 2)

Water inlet piping to contain the following components:

• Ball valve
• Wye Strainer

Water discharge piping to contain the following components:

• Pressure gauge
• Sample port
• Gate valve
• Check valve
• 2” SCH 80 PVC piping